Masjhuda - Project Quality Management - Jakarta, Jakarta Raya, Indonesia

Jusron Masjhuda

Jakarta, Jakarta Raya, Indonesia


More than sixteen years’ experience in QA/QC management with over seven years in supervisory role and over nine years as QA/QC Engineer, QC Welding Engineer, QC ( Welding, Mechanical, Piping and Structural ) Inspector of Offshore and Onshore Oil & Gas Construction components such as Jacket Platform, Petrochemical, Refinery, LNG pipeline and Shipbuilding.


Project Quality Management

Work History

Quality Control Consultant (Consultant Supervision)

SGS Indonesia – Industrial Division for Heidelberg Technology Center – Bogor Indonesia

May 2013 - September 2013

Job Function: To ensure that the structural steel fabrication and installation activities are completed meeting project quality levels.

√ Oversee inspection of steel structural pre-fabrication and installation activities conducted at contractors / sub-contractors facilities and at site.
√ Assist in structural material receiving inspections at site and review original material certificates for compliance to codes and specifications where required.
√ Ensure traceability is maintained for the fabricated part as stated in the project specifications.
√ Monitor and ensure the inspections are carried out to the required levels as mentioned in the ITPs.
√ Witness the dimensional control inspections on the pre-fabricated and as well on the installed parts.
√ Co-ordinate with other disciplines for interface activities, for example civil foundation interface with structural.
√ Monitor the structural welding activities inclusive of fit up / dimensional control inspections.
√ Monitor the contractor uses only qualified welders and follows the approved welding procedures.
√ Witness NDT / review NDT reports as required.
√ Final inspection, generate punch lists and follow up of the same for close out.
√ Verify Contractor, Subcontractor Quality management systems, plans, procedures, and processes are in place.
√ Monitor quality, issue non-conformance reports when quality deficiencies are noted and set in motion the corrective actions jointly with contractor.
√ Prepare weekly or monthly qualit

Site QC Representative at PT. Duta Cipta Perkasa Surabaya - East Java Indonesia

IHI E&C International Corporation

From October 2013

Directly assessed and evaluated the Contractor QA/QC activities during fabrication.
Participated in preparing and implementing of surveillance program to assess contractor work progress, ensure and or verify contractor work product are completed meeting project quality levels.
The intent of this activity is to recognize critical project stage and activities early enough to put adequate resource in place to identify and address potential quality issues, thus avoiding non conformity and deficiencies and their associated impact on cost and schedule.

Quality Assurance Specialist – KBR Company ~ Project Quality Management (Structural, Mechanical and Welding)

KBR Inc.

October 2012 - May 2013

Responsibilities and Duties

√ Ensuring Sub – contractor correct Assembly / Installation as per approved drawings and procedures.
√ Ensuring the equipment or material Edge Precision and Preparation.
√ Checking and accepting tolerable deviation.
√ Reviewing and Checking Welder’s Certificates.
√ Reviewing Project Specifications.
√ Reviewing Sub-contractor Procedure as per Specifications and Requirements.
√ Reviewing applicable WPS in line with Project specifications and requirements.
√ Review Recording of WPS, PQR and Material Certificates.
√ Monitoring, Managing, Supervise of Sub-contractor works as per requirement.
√ Planning of production and Inspection activities.
√ Final checking of Welding quality and dimension for release.
√ Reviewing of MDR report.
√ Compiling and reviewing MDR submissions for internal, 2nd and 3rd party approval.

Deputy QC Manager / QC Engineer

Saipem ENI - Karimun Yard Indonesia

May 2011 - September 2012

Responsibility and Duties :
√ An assistant project QC manager is in charge of revising the project work plans so that these satisfy all the needs and requirements.
√ An assistant project QC manager is entrusted with the evaluation of the issues that can crop up in future and can obstruct the smooth functioning of the project.
√ It is the duty of an assistant project QC manager to conduct a precise analysis of the project so that the firm gets some information about the returns that can be expected from the project.
√ An assistant project QC manager is also responsible for the speedy completion of all the assignments entrusted by the project manager.
√ The job of an assistant project QC manager involves maintaining good relationships with the supervisors and the workers.
√ An assistant project QC manager can help bridge the differences by highlighting them to the project manager. This way, an assistant project QC manager can act as a mediator between people he works under and people who work under him.
√ An assistant project QC manager is responsible for maintaining records regarding the on-site control functions.
√ An assistant project QC manager is also responsible for keeping his team updated with the changes in the organization through effective communication, presentations etc. This helps in transparency and also helps in building the morale of the team.
√ An assistant Project QC manager is also responsible for helping the project manager with quality-control programs to

QC Welding Engineer

JRay McDermott - Batam Indonesia

September 2009 - April 2011

McDermott is now a leading, stand alone engineering, procurement, construction and installation (“EPCI”) company focused on the offshore upstream oil and gas market worldwide. McDermott provides EPCI services related to offshore fixed and floating production facilities, pipelines and subsea systems primarily for national and major oil and gas companies.

Job Description :
√ Review Detailing Drawing NDT for Structure or Construction and Piping in the Project.
√ Determine Weld Preparation each joint connection in Detailing Drawing Structure & Piping before distribute to production.
√ Determine Welding Procedure Specification available to use in Detailing Drawing before distribute to production.
√ Check the Welding Documents such as Approved Welding Procedure Specification, Procedure Qualification Record and check all information for all variables and range of approval for that procedure.
√ Procedure and Specification Quality Control Plan.
√ Liaise to Client for Procedure and Specification for the project refer Client requirement.
√ Release and Approved Detailing Drawing Piping and Structure or Construction after finish the Process such as Welding Procedure Specification, Weld Preparation Joint, Non Destructive Test use for the Detail Drawing.
√ Collate all documents that involve during fabrication and submit to higher authorities.

Project involve:
- Platong Gas II Development Project, Chevron Thailand Exploration &
- Kipper Tuna Turrum Projet, Esso Australia Resources Pty.Ltd.
- North Rankin B Platform Sub – Structures Fabrication, Woodside Australia.
- Maersk Peregrino FPSO Module Fabrication Project, Maersk Denmark.
- Gorgon Project - Barrow Island LNG Plant, Chevron Australia

QA/QC Inspector Structural and Piping

PT McConnell Dowell Batam

February 2009 - September 2009

Responsible and Duties:

√ Prepare Daily Welding Activities.
√ Check all The Preparation before Welding.
√ Check Consumable.
√ Ensure Approved Shop Details Drawings have Weld Symbol Detail.
√ Ensure Proper sizes of Structural Steel members as per Approved Shop Detail Drawing.
√ Ensure Proper Cutting and Marking of Structural Steel members as per Approved Drawings.
√ Ensure correct Assembly / Fit-up according to approved detail drawings.
√ Ensure no Misalignment and Edge Preparation and Root gap are Acceptable.
√ Review and Check Welders Certificate.
√ Review Project Specifications.
√ Review Applicable WPS used for the project.
√ Procedure and Specification Quality Control Plan.
√ Monitor and Record NDT Status.
√ Stages of Production Activities.
√ Final Check on the Welding and Dimension.
√ Review NDT Report and Prepare Weld Summary Sheet for Approval by Client and Third Party.
√ Provide Copies of WPS, PQR and Material Certificates.
√ Complete, Check and Review Final Documentation prior submit to Company, Client and Third Party Inspector Approval.

Project involve: - Singapore Parallel Train for Refinery Project, Exxon Mobil Pte.Ltd.

Welding Inspector (QA/QC Engineer)

Drydocks World SE-Asia Batam - Indonesia

May 2006 - January 2009

Responsibilities and Duties:

√ Prepare Dock Trial & Sea Trial Procedure.
√ Prepare Inspection Test Plan.
√ Check the welding documents such as approved Welding Procedure Specification, Procedure Qualification Record and check all information for all variables and range of approval for that procedure.
√ Prepare inspection report.
√ Tracing ability of plate (material).
√ Fit up check, scantling check, vacuum test, air test, hose test, dye penetrant test & others visual inspection of welding.
√ Visual, routing, pressure test & others inspection of pipes.
√ Review RI film & others NDT Reports.
√ Alignment of Shaft & Propulsion System.
√ Inclining Experiment & Lightship Survey.
√ Collate all documents that involve during fabrication and submit to higher authorities.
√ Survey, commissioning, measurement, testing, etc.

Project involve:
- 53M Twin Screw Maintenance, Mohammed Bin Sagar Sdn Bhd.
- 65M Anchor Handling Tug Supply Vessel, Swire Pacific Offshore Ltd.
- 20200 DWT Cement Carrier, Belden Ship Holding Pte.Ltd.
- 40M Twin Screw Tug, Intone Pte,Ltd.
- Self Elevating Platforms, Jack-Up Barge BV.
- 65M Anchor Handling Tug Supply Vessel, Swire Pacific Offshore Ltd.
- Submergsible Barge, Swiber Offshore Pte,Ltd.

Snr. QA Supervisor

PT Japan Servo Batam

August 1998 - February 2006

Responsibilities and Duties:

√ Verification of compliance to applicable Process Control Specification & Control Plan.
√ Preparation of Assembly Instruction prior to approval.
√ Co-coordinating with Training Department for Manpower Qualifications.
√ To direct and coordinate technical personnel in performing inspections to ensure the workers compliance with established Assembly instruction, Process Control Specification and Control Plan.
√ To establish procedures to guide production and Manpower relating to specification restrictions, material, process requirements.
√ Contacts personnel of other agencies, Engineering or Client to exchange ideas, information or offer technical advice concerning process matters.
√ Jig and fixture fabrication related to process improvement.
√ Drive improvement project to increase Productivity, Process capability & Quality improvement.
√ Plan and Carry out Production under Controlled Condition and for Direct Liaise to Customer and Supplier, Monitor Quality Improvement of products as follows:
1. Information that describe product characteristics.
2. Work instruction as necessary.
3. Use of suitable equipment.
4. Use monitoring and monitoring device and etc.

Project Involved: - Stepping Motor and Rotating Equipment Manufacturing Company as Quality And Improvement the Products.
Improvement of Step Motor Assembly Lines Certificate,
December 28th, 2002, JSK Kiryu Japan.

Qualifications & Certifications

Bachelor Degree

Institut Teknologi Nasional Malang (ITN Malang)

Skillpages has been acquired by! is pioneering the way people find local services. Skillpages is the world’s premier directory of service providers.

Find out more

Jusron Masjhuda provides the following services:

Supported Countries
Choose your country